Why Your Recording Has an Echo, and How to Stop It

I get a lot of files where the voice is clear, but a second copy follows right behind it, a fraction of a second late. Two of these arrived in the same week this month. One was an event recorded in OBS. The other was a series of videos shot with a wireless mic and a webcam.

Both pointed to the same cause. The same microphone was recorded twice, through two different paths, and the two copies landed a little out of sync.

Why this is so hard to fix afterward

Room echo and doubled audio sound alike, but they're different problems. Room echo is a voice bouncing off hard walls. The de-reverb tools in iZotope RX handle it well, because the reflections are quieter than the voice and they fade quickly.

A doubled recording has a second full copy of the voice, almost as loud as the first. To restoration software, that second copy looks like speech, because it is speech. I can soften it, but I can't cleanly pull two copies of the same voice apart. In most cases the best fix is a new recording, or another copy of the event from a different source.

The cause is easy to find, and the fix takes a few minutes.

Check OBS for a second copy of your mic

OBS can pick up one microphone in several places at once. Open the Audio Mixer panel and watch the meters while you talk. Each meter that moves is a source carrying your voice. You want one.

These are the usual causes:

  • A mic set up twice. A mic chosen in Settings > Audio and added again as an Audio Input Capture source gets recorded twice.
  • The camera's audio. A video capture source, like a webcam or capture card, can bring its own audio along. If a mic is also feeding OBS another way, that's a second copy.
  • Desktop Audio. If your mic plays through your speakers or headphones, Desktop Audio can record it again on the way out.

Mute or remove every extra source until one meter moves when you talk.

Then open Advanced Audio Properties from the gear icon in the Audio Mixer. Find your mic in the Audio Monitoring column. "Monitor and Output" sends your mic to your headphones, and if Desktop Audio listens to the same device, OBS records your voice a second time. Set it to "Monitor Off" unless you need to hear yourself.

Check your wireless mic and camera

Wireless kits like the DJI Mic can send audio out of the receiver in more than one way. If the receiver feeds the camera over a cable and the computer over USB at the same time, and both end up in the recording, you get two copies with slightly different delays. A mixed or merged receiver mode can do the same thing when one transmitter sits close enough to pick up the other person.

Pick one path for each mic. Send the receiver to one device, and turn off the other device's input and its built-in mic.

Make a short test recording

Before a long session, record 30 seconds of talking, stop, and play it back on headphones. Listen for a slapback or a hollow, doubled sound. This catches routing problems before they cost you an hour of footage, and it's the habit I recommend most.

Record a backup inside the mic

The best protection is a second recording that never goes through OBS or the camera. Some wireless mics record inside the transmitter while they send audio to the receiver. If the main recording has a problem, the file in the mic is clean.

As an Amazon Associate I earn from qualifying purchases.

The DJI Mic 3 (paid link) records a 32-bit float backup inside each transmitter. A backup like that would have saved both of the recordings I mentioned above. Turn internal recording on before you start, and copy the files off the transmitters after each session.

If it already happened

Look for another source from the same event: separate tracks from a mixer or recorder, a phone or camera recording, a livestream archive, or the original file before it was exported. Any one of those is usually a better starting point than the doubled file. Send me what you have and I'll tell you what can be saved.

Common questions


Why does my recording have an echo?

A strong echo that follows the voice a fraction of a second later usually means the same microphone was recorded twice through two different paths, such as a mic source and a camera source in OBS. The two copies land slightly out of sync.

Can a doubled or echoey recording be fixed?

Light room echo can usually be reduced with de-reverb tools. A doubled recording, where a second copy of the voice is almost as loud as the first, rarely cleans up well. A different source from the same event, or a backup file from the mic, is the better fix.

How do I stop OBS from recording my mic twice?

Open the Audio Mixer and make sure only one source moves when you talk. Mute or remove extra mic, camera and Desktop Audio sources, and set the mic's Audio Monitoring to Monitor Off in Advanced Audio Properties.

Have a recording that needs help?

Send the file. I'll tell you what can be saved and send a sample of the fix before you pay.

Protected from bots by Cloudflare Turnstile.

Written by


Trevor O'Hare

Trevor O'Hare

Podcast Editor & Producer

I'm Trevor O'Hare. I edit podcasts for a living, backed by more than 20 years in professional audio. If your show needs a steadier sound, or your week needs fewer editing hours, that's what I do. Flat rates start at $100 per episode.

Learning voiceover? I also teach at VOTrainer.com.